Умирает винт?
| brestows |
|
Темы:
24
Сообщения:
189
Участник с: 06 апреля 2013
|
Добрый сегодня в логах нашел вот такое: TuxAdmin kernel: ata5.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0
TuxAdmin kernel: ata5.00: irq_stat 0x40000001
TuxAdmin kernel: ata5.00: failed command: READ FPDMA QUEUED
TuxAdmin kernel: ata5.00: cmd 60/00:00:67:8e:68/01:00:73:00:00/40 tag 0 ncq 131072 in
res 41/00:1b:4c:8e:68/00:00:73:00:00/40 Emask 0x1 (device error)
TuxAdmin kernel: ata5.00: status: { DRDY ERR }
TuxAdmin kernel: ata5.00: failed command: READ FPDMA QUEUED
TuxAdmin kernel: ata5.00: cmd 60/00:08:67:8d:68/01:00:73:00:00/40 tag 1 ncq 131072 in
res 41/40:00:4c:8e:68/00:00:73:00:00/40 Emask 0x409 (media error) <F>
TuxAdmin kernel: ata5.00: status: { DRDY ERR }
TuxAdmin kernel: ata5.00: error: { UNC }
TuxAdmin kernel: ata5.00: configured for UDMA/133
TuxAdmin kernel: ata5: exception Emask 0x1 SAct 0x0 SErr 0x0 action 0x0 t4
TuxAdmin kernel: ata5: irq_stat 0x40000008
TuxAdmin kernel: sd 4:0:0:0: [sdc] Unhandled sense code
TuxAdmin kernel: sd 4:0:0:0: [sdc]
TuxAdmin kernel: Result: hostbyte=0x00 driverbyte=0x08
TuxAdmin kernel: sd 4:0:0:0: [sdc]
TuxAdmin kernel: Sense Key : 0x3 [current] [descriptor]
TuxAdmin kernel: Descriptor sense data with sense descriptors (in hex):
TuxAdmin kernel: 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00
TuxAdmin kernel: 73 68 8e 4c
TuxAdmin kernel: sd 4:0:0:0: [sdc]
TuxAdmin kernel: ASC=0x11 ASCQ=0x4
TuxAdmin kernel: sd 4:0:0:0: [sdc] CDB:
TuxAdmin kernel: cdb[0]=0x28: 28 00 73 68 8d 67 00 01 00 00
TuxAdmin kernel: end_request: I/O error, dev sdc, sector 1936232012
TuxAdmin kernel: ata5: EH complete
TuxAdmin kernel: ata5.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0
TuxAdmin kernel: ata5.00: irq_stat 0x40000008
TuxAdmin kernel: ata5.00: failed command: READ FPDMA QUEUED
TuxAdmin kernel: ata5.00: cmd 60/08:00:47:8e:68/00:00:73:00:00/40 tag 0 ncq 4096 in
res 41/40:00:4c:8e:68/00:00:73:00:00/40 Emask 0x409 (media error) <F>
TuxAdmin kernel: ata5.00: status: { DRDY ERR }
TuxAdmin kernel: ata5.00: error: { UNC }Полез смотреть S.M.A.R.T. [[email protected]]>>sudo smartctl -A /dev/sdc ~/ :( smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.12.6-1-ARCH] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 120 2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0 3 Spin_Up_Time 0x0023 073 071 025 Pre-fail Always - 8369 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1286 5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0 8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 22145 10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1260 191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 75 192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0 194 Temperature_Celsius 0x0002 058 052 000 Old_age Always - 42 (Min/Max 14/48) 195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 3 198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0036 100 100 000 Old_age Always - 153 200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 4 223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0 225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1369 Полагаю стоит задуматься о том что бы заменить его на что-то более здоровое ?
kdeneur: https://github.com/brestows/kdeNeur
awesome WM 3.5 |
| dartsergius |
|
Темы:
18
Сообщения:
238
Участник с: 15 декабря 2011
|
Ну у меня при таких же симптомах файловая система не создавалась. Напряжение по 12в нормальное? Мб питания не хватает? |
| brestows |
|
|
Темы:
24
Сообщения:
189
Участник с: 06 апреля 2013
|
винт не один еще 3 винта сверху, которые работают нормально, бп хороший 550W должно хватать, ком нагружается редко даже очень максимум перехешировать торрент и откомпилить софт мой не более того :)
kdeneur: https://github.com/brestows/kdeNeur
awesome WM 3.5 |
| kurych |
|
|
Темы:
0
Сообщения:
1394
Участник с: 06 ноября 2011
|
Я бы для начала шлейф поменял. Если картина останется та же, тогда уже задумываться о замене винта. В любом случае своевременный бекап важных данных не помешает. |
| brestows |
|
|
Темы:
24
Сообщения:
189
Участник с: 06 апреля 2013
|
Ок спасибо, буду проовать смотреть что и как, потом отпишусь
kdeneur: https://github.com/brestows/kdeNeur
awesome WM 3.5 |
| vasek |
|
|
Темы:
48
Сообщения:
11340
Участник с: 17 февраля 2013
|
Может пригодится - я бы все-таки запустил полный тест $ sudo smartctl --test=long /dev/sd....
Ошибки не исчезают с опытом - они просто умнеют
|
| brestows |
|
|
Темы:
24
Сообщения:
189
Участник с: 06 апреля 2013
|
За ссылку спасибо, буду читать..... а как посмотреть результаты теста ?
kdeneur: https://github.com/brestows/kdeNeur
awesome WM 3.5 |
| lampslave |
|
|
Темы:
32
Сообщения:
4801
Участник с: 05 июля 2011
|
Результаты в том же smartctl -a отображаются (ближе к концу). |
| vasek |
|
|
Темы:
48
Сообщения:
11340
Участник с: 17 февраля 2013
|
Или по отдельности логи можно вывести так: - только атрибуты - $ sudo smartctl --attributes /dev/sda - только тест ….....- $ sudo smartctl --log=selftest /dev/sda - только ошибки ..- $ sudo smartctl --log=error /dev/sda
Ошибки не исчезают с опытом - они просто умнеют
|
| brestows |
|
|
Темы:
24
Сообщения:
189
Участник с: 06 апреля 2013
|
вот что мне показало:=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3
Device Model: SAMSUNG HD103SJ
Serial Number: S246JDWSC34540
LU WWN Device Id: 5 0024e9 002a0580e
Firmware Version: 1AJ100E4
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Jan 18 19:05:36 2014 FET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 40) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 9300) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 155) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 120
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 073 071 025 Pre-fail Always - 8369
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1286
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 22191
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1260
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 75
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 058 052 000 Old_age Always - 42 (Min/Max 14/48)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 3
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 100 100 000 Old_age Always - 153
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 4
223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1369
SMART Error Log Version: 1
ATA Error Count: 23 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 23 occurred at disk power-on lifetime: 10766 hours (448 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:00:00.951 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 00:00:00.951 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 00:00:00.951 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:00:00.951 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.951 IDENTIFY DEVICE
Error 22 occurred at disk power-on lifetime: 10766 hours (448 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:00:00.938 IDENTIFY DEVICE
00 10 f0 1a 91 19 40 00 00:00:00.938 NOP [Reserved subcommand] [OBS-ACS-2]
60 10 00 0a 91 19 40 00 00:00:00.938 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:00:00.938 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:00:00.938 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 21 occurred at disk power-on lifetime: 10766 hours (448 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:00:00.587 IDENTIFY DEVICE
00 10 00 12 53 ec 40 00 00:00:00.587 NOP [Reserved subcommand] [OBS-ACS-2]
00 10 00 12 52 ec 40 00 00:00:00.587 NOP [Reserved subcommand] [OBS-ACS-2]
ec 00 00 00 00 00 a0 00 00:00:00.582 IDENTIFY DEVICE
00 10 00 fa e4 ea 40 00 00:00:00.582 NOP [Reserved subcommand] [OBS-ACS-2]
Error 20 occurred at disk power-on lifetime: 10766 hours (448 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:00:00.421 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 00:00:00.421 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 00:00:00.421 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:00:00.421 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.421 IDENTIFY DEVICE
Error 19 occurred at disk power-on lifetime: 10766 hours (448 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:00:00.406 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 00:00:00.406 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 00:00:00.406 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:00:00.406 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:00:00.406 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Interrupted (host reset) 80% 22171 -
# 2 Short offline Completed without error 00% 10892 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Interrupted [80% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
kdeneur: https://github.com/brestows/kdeNeur
awesome WM 3.5 |