Базовая настройка: rc.conf по русски

#
# /etc/rc.conf - Main Configuration for Arch Linux
#
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# DAEMON_LOCALE: If set to 'yes', use $LOCALE as the locale during daemon
# startup and during the boot process. If set to 'no', the C locale is used.
# HARDWARECLOCK: set to "UTC" or "localtime", any other value will result
#   in the hardware clock being left untouched (useful for virtualization)
#   Note: Using "localtime" is discouraged.
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
# VERBOSE: Verbose level (from 1 to 8). man 3 syslog for level info
#
LOCALE="ru_UA.UTF-8"
DAEMON_LOCALE="no"
HARDWARECLOCK="UTC"
TIMEZONE="Europe/Kiev"
KEYMAP="ru"
CONSOLEFONT="ter-u16b"
CONSOLEMAP=""
USECOLOR="yes"
VERBOSE="3"
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# MODULES: Modules to load at boot-up. Blacklisting is no longer supported.
#   Replace every !module by an entry as on the following line in a file in
#   /etc/modprobe.d:
#     blacklist module
#   See "man modprobe.conf" for details.
#
MODULES=(tg3 b43 fuse usblp evdev psmouse vboxdrv)
# Udev settle timeout (default to 30)
UDEV_TIMEOUT=30
# Scan for FakeRAID (dmraid) Volumes at startup
USEDMRAID="no"
# Scan for BTRFS volumes at startup
USEBTRFS="no"
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
#
HOSTNAME="suhost"
# Use 'ip addr' or 'ls /sys/class/net/' to see all available interfaces.
#
# Wired network setup
#   - interface: name of device (required)
#   - address: IP address (leave blank for DHCP)
#   - netmask: subnet mask (ignored for DHCP)
#   - gateway: default route (ignored for DHCP)
# 
# Static IP example
# interface=eth0
# address=192.168.0.2
# netmask=255.255.255.0
# gateway=192.168.0.1
#
# DHCP example
# interface=eth0
# address=
# netmask=
# gateway=
interface=(lo !eth0 !ath0)
address=
netmask=
gateway=
# Setting this to "yes" will skip network shutdown.
# This is required if your root device is on NFS.
NETWORK_PERSIST="no"
# Enable these netcfg profiles at boot-up. These are useful if you happen to
# need more advanced network features than the simple network service
# supports, such as multiple network configurations (ie, laptop users)
#   - set to 'menu' to present a menu during boot-up (dialog package required)
#   - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network.d
#
# This requires the netcfg package
#
#NETWORKS=(main)
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
#   - prefix a daemon with a ! to disable it
#   - prefix a daemon with a @ to start it up in the background
#
# If something other takes care of your hardware clock (ntpd, dual-boot...)
# you should disable 'hwclock' here.
#
DAEMONS=(hwclock dbus iptables networkmanager fail2ban vnstatd ifplugd netfs avahi-daemon crond bluetooth)

#
# /etc/rc.conf - Main Configuration for Arch Linux
#
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime", any other value will result
#   in the hardware clock being left untouched (useful for virtualization)
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="ru_UA.UTF-8"
HARDWARECLOCK="UTC"
TIMEZONE="Europe/Kiev"
KEYMAP="ru"
CONSOLEFONT="ter-u16b"
CONSOLEMAP=""
USECOLOR="yes"
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
#
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
#
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(tg3 b43 fuse usblp evdev psmouse vboxdrv)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
#
HOSTNAME="suhost"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
#   - prefix an entry in INTERFACES with a ! to disable it
#   - no hyphens in your interface names - Bash doesn't like it
# 
# DHCP:     Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#
#Static IP example
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="dhcp"
ath0="dhcp"
INTERFACES=(lo !eth0 !ath0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
#   - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
 
# Enable these network profiles at boot-up.  These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
#   - set to 'menu' to present a menu during boot-up (dialog package required)
#   - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network.d
#
# This now requires the netcfg package
#
#NETWORKS=(main)
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
#   - prefix a daemon with a ! to disable it
#   - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng dbus iptables networkmanager fail2ban vnstatd ifplugd netfs avahi-daemon crond bluetooth)

interface=
address=
netmask=
gateway=

$ ps -ef | grep '\--daemon'